Write a Review

A full-featured, waterproof urban-inspired pannier that overcomes limitations normally found with waterproof bags. Offers exceptional external load flexibility, removeable internal organizers for digital devices, and a convenient external access pocket for keys and/or phone. - OCEANWEAVE 600D reclaimed fishnet polyester with waterproof polyurethane coating. - HYDRACORE liner provides an exceptional IPX5 waterproof rating. - Rixen & Kaul VARIO 2 spring-loaded hooks immediately adjust from 6mm-16mm, without any need for tools. - Rixen & Kaul lower SLIDE-LOCK and FLIP-LOCK hold panniers firmly in place. - Intuitive waterproof roll-down closure system. - Waterproof outer pocket. - Removeable 14.2-inches x10.2-inches padded laptop/electronics sleeve/organizer. - Removeable 10-inches x8-inches padded tablet/electronics sleeve/organizer. - External zippered pocket for keys/wallet, etc... - Keychain clips + 2 x Axiom keychains. - Independent main compartment and outer compartment compression/cargo straps provide exceptional load control. - Outer straps allow gear to be carried outside of the main cavity. Ideal for unplanned loads faced by commuters. - Strap control loops to protect against strap damage if straps are not secured. - Dual daisy-chain tie-down strips for additional load attachment. - Ultra-visible three-way 3M triangle logos. - Ultra-stiff Polypropylene backing plate. - Front and rear light clips. - Carry handle. - D-Rings built in to hook attachment points for additional luggage tie-down, or for attaching your own shoulder strap. - Volume 22.6L / 1379 cu/in - Weight 1220g / 2.69 lbs (incl. laptop sleeve and tablet sleeve) – (995g / 2.19 lbs without sleeves) - Dimensions 47x28.5x13.5cm / 18.5-inches x11.3-inches x5.3-inches main compartment 33x18x7.5cm / 13-inches x7-inches x3-inches pocket - Pannier sold individually

Bike to hike and back again has never been easier. Based on the iconic Fjallraven Verdag backpack, the Cave Pack has been shaped to nestle into the Coolcave like an arctic fox in its den. Lift the pack out of the Coolcave and sling it on your back using the padded shoulder straps. Equipped with a padded laptop compartment and large and small pockets, the Specialized/Fjällräven Cave Pack organizes and protects your most important belongings. - 20L capacity. - Easy-access pocket. - Fully padded laptop compartment. - Large front pocket. - Easy-carry handles. - Compatible with Coolcave pannier.

Topeak's MTX BeamRack is an awesome way to add touring capacity to bikes that won't accept conventional racks, such as dual-suspension mountain bikes. The quick-release mount clamps firmly to your seatpost and this rugged rack boasts durable aluminum construction capable of supporting up to 20-pounds with ease.

Be it the fireworks of a finale, an ideal rhythm, climbing on the top, or a deep, dark place extracting the last kilojoule of effort on your bike split, you want to adjust your gear with the twitch of a finger. eTap Blip satellite shifters allow you to shift when you want, where you want. - Limitless remote shifting positions for drop and aero bars - Wired shift buttons can be positioned however the rider prefers - Connect to Blip Box or drop bar eTap levers - Compatible with SRAM RED eTap shift/brake controls

Engineered with incredible night piercing power, the newly designed Metro Plus™ 800 headlight and Hotshot Pro™ 150 tail light combo set delivers optimal lighting coverage with exceptional brightness and clarity wherever the road takes you. Fire up an intense 800 lumens forward and 150 lumens backwards, knowing the cycling-tuned long-range and extra-wide beams maximize your line of sight and visual profile. Not only limited to night, both lights pack DayLightning® mode to make you stand out in broad daylight, giving you the advantage any time and anywhere you ride. Patent pending. Metro Plus™ 800 USB Headlight: - Powerful 800 lumen output with 9 light modes - Built-in 24/7 Safety Technology® gives you a powerful selection of night and day modes (Boost - High - Medium - Low - SteadyPulse® - DayLightning® - Triple Flash - Zoom - Walking) - SteadyPulse® mode alerts night time motorists with pulses while constantly lighting your path - DayLightning® mode emits lightning-like flashes to highlight your presence in the brightest of daytime hours - Enhanced Cycling Optics™ (ECO) expands your visibility with an extra-wide and long-range beam - USB rechargeable Li-ion battery - Low battery indicator - Light activation lockout prevents accidental light activation - Light mode memory saves the mode you're in before the light is turned off - Rugged, water-resistant design only weighs 140 grams - Side illumination ports highlight your presence to nearby motorists - 2nd generation Locktite™ tool-free handlebar mount securely clamps to 22mm to 32mm diameter handlebars Hotshot Pro™ 150 USB Tail Light: - Powerful and efficient single LED blasts 150 lumen flashes (90 lm steady) - Built-in 24/7 Safety Technology® gives you a powerful selection of 6 day and night modes (Steady - Zoom - SteadyPulse® - Triple Flash - DayLightning® - Random Flash) - Freely adjust the brightness of Steady mode and the flash tempo of the flashing modes with the simple 2 button interface (patent pending) - SteadyPulse® mode features a steady beam to help motorists gauge their distance while overlapping pulses keeps them alert at night - DayLightning® mode emits lightning-like flashes to highlight your presence in the brightest of daytime hours - Zoom mode signals those around you with gentle changes in brightness - Enhanced Cycling Optics™ expands your presence with an extra-wide and long-range beam - USB rechargeable internal battery - Low battery indicator - Light mode memory saves the mode you're in before the light is turned off - Compact, water-resistant design weighs only 59 grams Patent pending. *Features and specs are subject to change without notice.

A Burley Ballz Thru Axle is required for any bike with a 12mm rear thru axle to use the Coho XC (stock thru axles are not able to accommodate any sort of axle mounted hitch system). The Burley Ballz Thru Axle is not compatible with all carbon fiber bike frames (consult manual). - Official Burley Ballz adapter for bikes with 12mm rear thru axles - Includes both the thru axle and Ballz hitch mounts - Quick and easy installation - Specially designed for use with the Coho XC

The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.

Following a design update, the HIGHTREK clip-on mudguard set impresses with its sporty look. It can be mounted to seat tube diameters of between 28 and 32mm. The well-thought-out universal fastener and clip enable the mudguard to be mounted and removed quickly without any tools.

The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.

The new 8-Bit System is a group of multi-tools designed to work together to solve most trailside fixes. They are lightweight, strong, versatile, and small enough to fit in a jersey pocket or riding tool wrap. Three multi-tools begin the 8-Bit System: 8-Bit Chainbreaker + Utility Knife Multi-Tool, 8-Bit Tire Lever + Rim Dent Remover Multi-Tool, and 8-Bit Pack Pliers. A total of 22 functions between the three tools will keep you rolling to the next town or trailhead. - 17 functions: spoke wrench; valve core wrench; flat head #3.5 and Phillips #2 screwdriver bits; 2, 2.5, 3, 4, 5, 6, and 8mm hex; and T10, T25 Torx-compatible bits; install and remove master links; clear tire sealant clogs from valve stem; tighten valve stem lock nut - Magnets keep all bits in place - Ball detent swivel head helps access hard-to-reach places - Handle doubles as breaker bar for extra torque when head is bent - 8mm hex bit tested to over 40 Nm torque - Pliers works with 9-, 10-, 11- and 12-speed master links and chains (not compatible with Campagnolo 12-speed chains) - Master Link storage is compatible with SRAM PowerLock Link, Shimano Quick-Link, KMC Missing Link and other similar master links (not compatible with Connex Links by Wipperman)

The MSW PC-150 composite water bottle cages are a great value, providing easy use and are less likely to scratch the finish on most water bottles. - Composite construction - Does not include mounting bolts - Embossed MSW logo

Portland Design Works' Fenderbot Taillight shines brightly to enhance your visibility when the sky turns dark. It boasts a 1-watt LED with three modes and precision reflector to notify others of your presence. And, the Fenderbot bolts directly to your fender so it's always on your bike. - Bright red LED and precision reflector - Bolts directly to fender to prevent theft - Weatherproof exterior for all season riding - Weight: 62 g (2.2 oz) - Runs on 2xAAA batteries (included) - Lifetime PDWarranty

- Front rack with foldable sides for an expandable platform size - Sturdy powder-coated alloy construction - Can be attached to brake mounts or threaded accessory eyelets - Adjustable legs fit 26" – 29" frame sizes - 22lb weight limit - Disc Compatible: No

A clean bike is a happy bike! Keeping your bike clean is an essential part of bicycle maintenance, ensuring better performance, increased safety, easier repairs, increased life of all parts of the bike, and more fun on your next ride! Pedro's Pro Brush Kit offers a set of four unique brushes designed specifically to easily and quickly clean all parts of the bike. Made with the user experience and durability in mind, each brush's ergonomic handle fits well in your hand while offering unmatched durability. - Large Frame and Wheel Brush - Toothbrush; ideal for cogs, derailleurs, and chainrings - Cone brush for hard to reach spots - Parts cleaning brush for applying degreaser - Logo bag for storage and travel. - Perfect when paired with Pedro's degreaser and cleaner products (each sold separately)

Prestalever is Quicker and Speedier than anything you've ever used. Our Patent-Pending Rim Hook with Honeycomb reinforced Box-Section Design is the key to our faster, safer, easy-to-use tool. Remove tires in seconds! Prestalever is Quicker and Speedier than anything you've ever used. Our Patent-Pending Rim Hook with Honeycomb reinforced box-section is the key to our faster, safer, easy-to-use tool. As you scoop the tire bead with the Prestalever, the slot underneath we call the "rim hook" naturally drops inside the rim. It prevents the Prestalever from slipping out, so you don't drop the bead. The rim hook stops the Prestalever at an easy-to-hold angle on the side of the rim. Then you simply glide the lever around the rim, and the tire peels-off as you go. The Prestlever is made of slippery Nylon, greatly reducing the force needed to remove tires. When you're done, twist the Prestalever 90 degrees to raise the rim hook out of the rim. Our box-section design allows the twist-action to easily stop at 90 degrees so the lever slides out easily. Install tires without strain. Our thick tip on the tire installer-end prevents catching and pinching tubes inside your tire. The bead-grabbing edge gives the right balance between leverage and lifting force, making it as easy as possible to complete tire installation. Presta Core tool is now essential. Even Bicycle Presta tubes now include removable cores. This gives you the added option of using tire sealant inside the tube of your standard tire. Removable cores are not always fully tightened at the factory. A loose core could cause slow leaks, or could even become unscrewed while using inflation devices. Tubes should be checked during installation and regularly afterwards for Presta core tightness. Don't carry an extra tool for chains! The Prestalever quick-link breaker is an effective emergency tool if you need to remove your chain on the road. The Patented design is the creation of Prestacycle's good friend and associate – cycling engineer Tomo Ichikawa. It removes the quick-link, which is the only function you need. When quick links are installed, pedal pressure can lock the installed quick link without any tools. For regular chain service, we still recommend a quick link tool, but with our feature, you no longer need to carry a separate tool with you on the bike. Quick-link removal Instructions: Place the quick Link near the top of the crank Jump the chain forward one tooth so the quick-link stands-up Use the slot on the Prestalever to push down FIRMLY. (The crank tooth will support the other end from underneath.) T-handle Tubeless Tire Plugger (optional parts required – Available 12/15/2021) The center of the Prestalever has threads which accept our Tubeless tire plugger. It then forms a T-Handle for effective, centered pushing of the included "Bacon Strips" used to seal large cuts in Tubeless tires. Third-hand Tool for Hand Installation Certain tires have delicate beads. Tire manufacturers recommend hand-installation only. The Prestalever can be used as a "third-hand" tool. When you hand-install the bead in one direction, the tire starts lifting-out at the other end. Insert the lever at one end to hold the bead, then use BOTH hands to install the tire from the other end. Tubeless Tire Removal (or any Difficult Tire) The Prestalever is the #1 tool for removing difficult tires. Using two or three can help with the toughest tire and wheel combo's. Insert a lever, but do NOT flip it yet. The rim hook will hold the lever in place, but unlike traditional levers that hook onto spokes, the bead will NOT be tensioned. You can still fit-in more Prestalevers. Insert the levers spaced about 6 inches apart, then flip them all … one-at-a-time. Even the toughest tires will come right off the rim in seconds. Prestalever is different… designed from the start with real-world experience on bicycles. Specifications: - One-end: purpose-designed Tire Remover - The-other-end: purpose-designed Tire Installer - Presta Valve Core tool - Quick-link Chain breaker. - Threads make it a T-Handle Tubeless Tire plugger (plugging kit additional). - Use multiple levers for tough, delicate tires like Road Tubeless and Gumwall. - Dimensions: 100mm x 13mm x 12mm - Weight: 13 grams Disclaimer: Check with the manufacturer of your wheels and tires to verify application and fit. Some manufacturers specify hand installation and removal only. Always follow Manufacturer guidelines for tires and wheels.

Made from tough steel and reinforced with extra material at the highly stressed wrench openings, Park’s shop-quality Pedal Wrench is built to easily install and remove pedals, and to last and last. It has 15mm and 9/16-inch precision openings to fit all pedals. And it boasts a long, round, vinyl-coated handle that won’t dig into your hand and provides optimum leverage. There's even a hole in the end of the wrench for hanging it on your toolboard.

• Glass reinforced nylon construction • Fits standard bottles • Hardware included • ~ 28g

The included 9 function Multi Tool contains your most used tools and is designed to live inside your stem/steerer tube. Never get stuck without a Multi Tool on a ride ever again. - 2, 2.5, 3, 4, 5, 6, 8mm - T25 Torx - Flat Head Screwdriver - A stripped down version of the EDC tool containing a 9 function multi-tool neatly stored in your steerer tube - Very easy to install without removing your star nut or threading your steerer tube

Let everyone know your coming with Sunlite's I Love My Bike Bell. It makes the classic "ring-ring" sound that everyone loves. It fits most bars and can be used right or left handed.

For riders looking for comprehensive coverage to protect high-risk areas of a Steel Hardtail MTB frame. Bike protection provides great benefits starting from the aesthetics side, right over to the functionality/durability of the bike. Bike protection kits are high-quality polyurethane films that are applied to the bike to protect it from scratches, rock chips, and/or scuffs caused by trail debris, rocks, cable rash, heel rub, chain slap and other elements while out on the trails. All RideWrap protection accessories have been designed to give riders leading coverage for their dollar. All RideWrap protection kits are made with high-quality, bike-tested RideWrap materials that feature durability, stain resistance, self-healing properties, and a 10-year warranty. - Gloss clear film - Fits all makes, models and sizes - Designed for maximum coverage with minimal trimming - Designed around hardtail steel mountain bike geometry - The Steel MTB Kit includes protection for toptube, full downtube, 4 stays, seat tube, and extra pieces to provide approximately 60% frame coverage - Made in Canada with high-quality RideWrap materials - Kit is packaged with instructions, pre-install cleaning wipe, install solution concentrate, squeegee, microfiber cloth, and RideWrap sticker sheet

- End link locking point for extensive holding power - 4-sided 3t manganese steel chain links - 5 digit resettable combination over 100,000 codes - Patent pending lock head design - Combo Safe Program - Product dimensions: Length 120cm - Product weight: 7.35 lbs

- Installs and removes threaded cups for 386Evo cranks - Socket type tool for 1/2" drive socket wrenches

This saddle rail bracket is designed to be used with the Flare and TraceR, this product will fit any standard rail design saddle.

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

- Sram XD and XDR freehub for Direct Drive trainers (Drivo and Direto's family, Suito, Turno, Kura, Turbo Roteo and Volano). - Compatible with 12 speed cassette.

DT Swiss Wheel bags

Rack 'em up! - Add carrying capacity while looking stylish. - Perfect for hauling your favorite belongings. Product details - Compatible with MIK accessories - Alloy heavy-duty 12mm diameter bars - Carrying capacity up to 25kg or 55lbs. - Stainless steel hardware included - Rear rack designed to be compatible with Electra Vale models

THE QUINTESSENTIAL PACK FOR CARRYING HEAVY LOADS OVER LONG DISTANCES. The Pack fits into the bike’s main triangle, providing a large space for bulky items — anything from cooking gear and tent poles, to heavy tools on longer expeditions and bikepacking trips. The resulting low centre of gravity is spread along a narrow, central plane, resulting in a Pack that has minimal effect on handling while offering a high volume of storage space. It’s constructed from a lightweight fabric, custom milled to Apidura’s specifications and welded together at the seams to create a watertight seal. Zippers with protected closures ensure that kit stays dry, even in a sustained downpour. A battery lead/hydration hose port is handy for charging devices or staying hydrated on the road. Features - Lightweight waterproof laminate, developed specifically for Apidura - Carbon-friendly attachment straps for a strong hold - Dual interior compartments, with removable internal divider - Interior storage pockets keep contents organised - Protected battery/hydration hose port - Reflective graphics for increased visibility Materials - The Expedition Full Frame Pack is cut from a three-layer laminate fabric that was developed specifically for Apidura. The material is lightweight, and is highly resistant to tears and abrasion. Notably, it’s welded together at the seams, creating a watertight seal that ensures complete waterproofing. Care - Hand wash, using a mild diluted soap if necessary. Afterwards, let it air dry. - Do not machine wash, machine dry, or iron.

Kit-match with a new customizable high-grip carbon cage! Customize Your Cage Colors - Personalize your look with Raptor Talons available in multiple colors - High-grip carbon cage with approx 6lbs grip force - Svelte design for a streamlined look - Weight: 1.0oz (30g) - Pair with the hyper-reflective Cool Shot insulated bottle Grip Force - Approx 6lbs grip force for excellent bottle retention Optimized Carbon - Unidirectional carbon inside and 3K carbon weave outside Ideal Uses - Road - Triathlon (Aerobar and Frame) - Gravel - Mountain - Weight: Approx 30g (1.07oz) - Grip: Approx 6lbs - Construction: Carbon Fiber - Includes: Corrosion resistant Black Zinc screws - Warranty: Limited 3 Year

Made of durable and waterproof polyester fabric, the ORTLIEB Ultimate Six Classic is a compact handlebar bag that plays a key role in the gear management plan of all bike touring enthusiasts.